How to spot cell imbalance in your EV batteries

Tom Bateman

If a vehicle in your fleet starts needing extra charging stops or struggles to reach its usual charge level, your workshop needs to find out why.

Cell imbalance occurs when cell groups within an EV’s high-voltage traction battery operate at different states of charge (SoC). Changes in vehicle behaviour might raise your suspicions, but identifying it requires a closer look at the battery data.

At Rotronics, we help fleet workshops choose equipment suited to their vehicles. Here’s how your team can work through the checks, starting with driver reports.

Check for unexplained EV range loss

Compare actual journeys from similar starting charge levels. Account for the payload, weather, driving habits and use of heating or air conditioning. Tyre pressure and other sources of drag can also affect how far the vehicle travels. Look for a repeated drop in range that these factors don’t explain.

Look for changes in charging behaviour

Ask your drivers and fleet staff to report sessions that differ from the vehicle’s normal charging pattern. Watch for:

  • Charging repeatedly ending before the usual charge target.
  • Charging slowing unexpectedly under comparable conditions.
  • The vehicle reporting a full charge sooner, followed by noticeably less usable range.

If one cell group reaches its upper voltage limit before the others, the battery management system (BMS) may slow or stop charging.

Note the battery temperature, charge level at the start and charger used. Compare sessions under similar conditions over several days or weeks. This helps your workshop work out whether the change is linked to the vehicle or differences in the power available from the charger.

Watch for unexpected drops in battery percentage

A sudden, unexplained drop in the displayed battery percentage can be a warning sign of cell imbalance. Ask drivers to note the percentage before and after the drop, where possible, and whether it happens repeatedly.

Your technician can then compare those reports with cell group voltage readings to investigate possible imbalance. The dashboard percentage alone can’t confirm it.

Read EV battery warnings and fault codes

Use a compatible diagnostic tool to read battery-related diagnostic trouble codes. Relevant codes may concern excessive voltage variation, cell voltage limits or voltage-sensing faults.

Save the exact code and any available freeze-frame data, which captures operating conditions when the fault was detected.

Interpret the code alongside live readings. Remember that voltage variation codes sometimes pop up when there isn’t a genuine battery cell problem. An absence of warnings or stored codes doesn’t rule out imbalance either.

Compare cell group voltages

Use a diagnostic tool that can read cell group voltages for that vehicle. A generic OBD-II scanner may not provide this data. Compare:

  • The highest and lowest reported cell group voltages.
  • The difference between them, often expressed in millivolts.
  • Any groups whose readings sit apart from the main cluster.

For example, if the highest reading is 3.680V and the lowest is 3.620V, the voltage spread (‘cell delta’) is 0.060V, or 60mV.

There isn’t a single voltage spread limit you can apply to every EV. Assess the result against the manufacturer’s requirements and specified test conditions. A small difference may be normal; a larger one needs interpretation to establish whether it reflects SoC imbalance, cell condition or a measurement problem.

Check whether the voltage difference remains

After any resting period specified by the manufacturer, check whether the voltage difference is still there.

During charging, watch for a group getting close to its upper voltage limit before the others.

When the battery is supplying power, look for a group whose voltage drops more than the others or gets close to its lower limit sooner.

Check whether the same cell groups keep showing higher or lower voltages than the others. Record which groups they are and how much their voltages differ.

Also note the battery’s charge level and temperature, plus whether it’s resting, charging or supplying power. This helps you compare readings taken under similar conditions.

What to do if you find cell imbalance

Bring the driver reports, fault codes and voltage readings together to decide what to check next. If your checks confirm cell imbalance, follow the manufacturer’s guidance on the next steps.

Balancing may help bring the cell groups to similar charge levels. If the cells have degraded, balancing won’t restore their lost capacity. In that case, the affected module or battery pack may need replacing.

To discuss EV battery checks for the vehicles in your fleet, contact Rotronics. We can help you match equipment, training and technical support to the work your team needs to carry out.

Join our newsletter